54-60Dodgetrucks at Yahoo! Groups

Re: 383 dodge eng parts

William Kirkland — Tue, 10 Nov 2009 01:59:06 GMT

ERIC, In what state are you in? How much are one set of heads? Thanks, Bill ERIC, In what state are you in? How much are one set of heads? Thanks, Bill

Re: 1957 sweptside

Roy Oliva — Tue, 10 Nov 2009 01:56:49 GMT

there were removed because it was working truck serious rot, wood bed bad shape,so my uncle replace w/usable bed ________________________________ From: Reg

383 dodge eng parts

Eric H — Tue, 10 Nov 2009 01:41:31 GMT

hello everyone i have a few 383 chrysler big block engine parts here is a list. 2: blocks been bored think at .30 over 2: crankshafts main on rods and mains 2:

Re: 1957 sweptside

Reg Evans — Tue, 10 Nov 2009 00:53:04 GMT

Just curious.......why were the fins and bed removed. ... From: Roy Oliva Subject: [54-60DT] 1957 sweptside To:

55 Windsheild

bobnorris2002 — Tue, 10 Nov 2009 00:31:19 GMT

Sorry wrong link on that last post! http://www.moparbob.com/gallery/rwx_gallery/10-31-09_1202.jpg

55 Windsheild

bobnorris2002 — Tue, 10 Nov 2009 00:29:20 GMT

Anybody know what windshields will fit in a 55?? I just found a cab and were making a rat rod out of it. http://www.cartalklive.com/scansoft.exe

1957 sweptside

Roy Oliva — Mon, 09 Nov 2009 23:49:07 GMT

I have 57 sweptside its been in family form day 1, it has 39000 orig mi , the bed & fins were taken off in 1970 and replaced with stepside bed. I'm in progress

Wanted: Parking Light Lens for a 54 Dodge C1-B truck

tim0068 — Sat, 07 Nov 2009 16:00:00 GMT

Anyone have a lens that you would be willing to sell?

55 H-series (2 ton) FS or trade

Dan — Mon, 02 Nov 2009 23:17:24 GMT

I have a 1955 Dodge grain truck that I don't have any big plans for. If it doesn't sell I might make a car hauler out of it, someday.... Very solid truck. No

Re: sticky hand brake cable

Doug — Mon, 02 Nov 2009 07:02:55 GMT

Hi, WD-40 is not a very good penetrant. try something like PB Blaster, Kroil, Brute Force, etc. soaking it in diesel fuel will also loosen it up. if the casing

Re: sticky hand brake cable

Gary Robertson — Sun, 01 Nov 2009 16:43:11 GMT

On my 64 TW the e brake cable has seized completely from rust and has again due to holes worn in the sheath and water getting in. Remove the cable and hang

sticky hand brake cable

jeromeowens — Sun, 01 Nov 2009 14:36:33 GMT

My hand brake cable is sticky. When I release the hand brake tension in the cab the hand brake drum doesn't fully open. The springs on the hand brake seem

Re: Reassembly '57 d100

Ford David Sr — Sat, 31 Oct 2009 21:51:51 GMT

I have a 54 dodge truck and what I used is a tractor inter tube works great ... From: jeromeowens Subject: [54-60DT] Reassembly '57 d100 To:

Re: Reassembly '57 d100

tmhnjh — Sat, 31 Oct 2009 15:16:41 GMT

For the front nose use seam sealer. Get in caulk tube form. You can get it from Eastwood or a body shop supply. The rear fenders to the bed, get rubber fender

Reassembly '57 d100

jeromeowens — Fri, 30 Oct 2009 20:27:19 GMT

Does anyone know the proper or best product to use between the front sheet metal and the fenders during reassemby? Is there some sort of welt or gasket that is