http://groups.yahoo.com/group/GenesisRadio/ GenesisRadio Fri, 24 May 2013 22:13:49 GMT Bob Bownes http://groups.yahoo.com/group/GenesisRadio/message/17692 http://groups.yahoo.com/group/GenesisRadio/message/17692 Bruce, Pictures uploaded to http://www.fastbobs.com/pictures/G11/ sweeps of the LPF with a network analyzer are in the plots subdir fwiw Bob Fri, 24 May 2013 19:15:58 GMT bownes http://groups.yahoo.com/group/GenesisRadio/message/17691 http://groups.yahoo.com/group/GenesisRadio/message/17691 G11 worked prior to any mods. Sound card is onboard SC of dell laptop. I moved to eliminate mac from problem set. Input vol is now turned down. Works fine (rx) Fri, 24 May 2013 19:02:09 GMT Bruce kf1z http://groups.yahoo.com/group/GenesisRadio/message/17690 http://groups.yahoo.com/group/GenesisRadio/message/17690 Also.... I just read one of your first posts... You said you have volume cranked all the way up on MIC input? ( should be line-input , not mic) did you test Fri, 24 May 2013 18:52:44 GMT Bruce kf1z http://groups.yahoo.com/group/GenesisRadio/message/17689 http://groups.yahoo.com/group/GenesisRadio/message/17689 Here's another check to make... With the MBF board completely disconnected from G11... Check continuity between the arrows marked on the attached picture.... Fri, 24 May 2013 18:37:48 GMT Bruce kf1z http://groups.yahoo.com/group/GenesisRadio/message/17688 http://groups.yahoo.com/group/GenesisRadio/message/17688 Would you upload some good clear pics of the G11 board, without the filter board, and then of the filter board? Also, remove the mbf board. use the second RX Fri, 24 May 2013 18:05:40 GMT Bob Bownes http://groups.yahoo.com/group/GenesisRadio/message/17687 http://groups.yahoo.com/group/GenesisRadio/message/17687 Bruce, I hope the move went well! I'm using the primary antenna port, the one closest to the power connector. The cable has ground to ground., the uC mod is Fri, 24 May 2013 17:15:05 GMT Bruce kf1z http://groups.yahoo.com/group/GenesisRadio/message/17686 http://groups.yahoo.com/group/GenesisRadio/message/17686 Also, I would double check which antenna connector you are using, and make sure that the "Second RX input" box in GSDR is checked or unchecked as it should be. Fri, 24 May 2013 17:06:48 GMT Bruce kf1z http://groups.yahoo.com/group/GenesisRadio/message/17685 http://groups.yahoo.com/group/GenesisRadio/message/17685 I haven't followed the issue..... because of my move... And don't know what checks you have done. But back to the beginning. The first step for me, would be to Fri, 24 May 2013 16:36:12 GMT n1rx http://groups.yahoo.com/group/GenesisRadio/message/17684 http://groups.yahoo.com/group/GenesisRadio/message/17684 Sold. Thanks for the bandwidth. -Bruce. Fri, 24 May 2013 15:49:44 GMT Alexandar Tomic http://groups.yahoo.com/group/GenesisRadio/message/17683 http://groups.yahoo.com/group/GenesisRadio/message/17683 Hello Angel, Thank you very much. Here you can watch low qualiti video from YU1EXY location http://www.youtube.com/watch?v=BvDgm4PuG-k This is from 2010 but Fri, 24 May 2013 15:44:39 GMT bownes http://groups.yahoo.com/group/GenesisRadio/message/17682 http://groups.yahoo.com/group/GenesisRadio/message/17682 The pins are all pulled high by resistors so you need to ground pins to select the band filter you want. If the connector is defines as pin 1 is the pin that Fri, 24 May 2013 14:50:14 GMT Bruce kf1z http://groups.yahoo.com/group/GenesisRadio/message/17681 http://groups.yahoo.com/group/GenesisRadio/message/17681 database.xml But, most of it will change on a new system. Likely the only thing that won't change will be the Si570 calibration. Most everything else is Fri, 24 May 2013 14:13:05 GMT Angel http://groups.yahoo.com/group/GenesisRadio/message/17680 http://groups.yahoo.com/group/GenesisRadio/message/17680 Alex and Team, Good luck in contest this weekend! I do not know cw, but took part on eu psk and other rtty contests over the last weekends using cwexpert and Fri, 24 May 2013 09:02:57 GMT k4lcd@... http://groups.yahoo.com/group/GenesisRadio/message/17679 http://groups.yahoo.com/group/GenesisRadio/message/17679 Please join by clicking the link: http://groups.yahoo.com/group/sdr-users/join This discussion group is for people interested in the state of the art of the Fri, 24 May 2013 05:17:39 GMT ae7ip http://groups.yahoo.com/group/GenesisRadio/message/17678 http://groups.yahoo.com/group/GenesisRadio/message/17678 my old computer xp pro 32 bit new computer win 7 64 bit What file(s) do I need to move from my old computer to the new one to move the calibration data for the