KawaSixes at Yahoo! Groups

Re: F Y I

Tim — Sat, 31 Oct 2009 11:47:23 GMT

GREAT Link, Thanks for posting!

Custom rear master cylinder for a Z1300

Reverse Trike — Fri, 30 Oct 2009 16:56:50 GMT

OK, here's the link I left out to my previous post on this rear master cylinder for a Z1300 - http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=260497817658

Re: Valve clearances

Reverse Trike — Thu, 29 Oct 2009 15:32:07 GMT

KZ1300 covers do NOT interchange with ZN1300 covers! There are so many differences between KZ & ZN motors I made a list somewhere on my site, maybe on the FAQ

Re: Valve clearances

LC — Wed, 28 Oct 2009 12:33:47 GMT

Yes. Same basic engine. KZ or ZN. Larry Colin On Tue, Oct 27, 2009 at 10:19 PM, tom whitehead

Re: Valve clearances

Horacio Colombo — Wed, 28 Oct 2009 11:41:13 GMT

Hi Tom, This clutch cover is excelent, I can check the oil level even even sitting on the bike and looking down. I dont know if it's compatible, we should ask

Re: Valve clearances [1 Attachment]

tom whitehead — Wed, 28 Oct 2009 02:19:09 GMT

Nice. will it work on my ZN? ... From: Horacio Colombo Subject: Re: KawaSixes. Valve clearances [1 Attachment] To:

Re: Valve clearances

tom whitehead — Wed, 28 Oct 2009 02:16:24 GMT

ditto on the valve issue. My thought is run them on the lower side and when they do wear the will have a couple of thousanths additonal before they need to

Re: Iron Bolt Bruce and our expectations.

tom whitehead — Wed, 28 Oct 2009 02:14:27 GMT

I agree as well. I didn't read any of those posts so no loss. I do agree with a sliding scale as some of the posts are by regulars who do post useful and

Re: F Y I

kzcsi — Wed, 28 Oct 2009 01:17:06 GMT

Thanks TH, That was a good link. Bill

Re: Iron Bolt Bruce and our expectations.

kzcsi — Wed, 28 Oct 2009 01:06:41 GMT

Hi Folks, Well, we lost KingMobely and IronBoltBruce. I'm sorry about KingMobely, but couldn't care less about Bruce's decision. I see that we've exceeded our

Re: Iron Bolt Bruce and our expectations.

Chris — Tue, 27 Oct 2009 23:00:15 GMT

Well done Bill you have handled that well. I agree with the bit of lattitude to other motorcycling issues and other sixes while at the same time the priority

Re: Iron Bolt Bruce and our expectations.

tom dotter — Tue, 27 Oct 2009 21:41:57 GMT

Works for me. Tom ________________________________ From: kzcsi To: KawaSixes@yahoogroups.com Sent: Mon, October 26, 2009 7:40:52 PM Subject:

F Y I

tackelhappy — Tue, 27 Oct 2009 15:57:18 GMT

Another 6 cylinder comparison of old. http://www.cycleworld.com/article.asp?section_id=3&article_id=1744

Re: Iron Bolt Bruce and our expectations.

tackelhappy — Tue, 27 Oct 2009 15:35:16 GMT

Sounds good to me. glenn

Re: Iron Bolt Bruce and our expectations.

Bob CF-PLL — Tue, 27 Oct 2009 13:30:13 GMT

CHECK! Bob Owen Sound, Ontario, Canada. ... From: LC Subject: Re: KawaSixes. Re: Iron Bolt Bruce and our expectations. To: