http://tech.groups.yahoo.com/group/Sumo11users/ Sumo11 Robot Controller Thu, 19 Feb 2009 16:16:40 GMT RidgeSoft http://tech.groups.yahoo.com/group/Sumo11users/message/534 http://tech.groups.yahoo.com/group/Sumo11users/message/534 RidgeSoft is pleased to announce the availability of the RoboJDE Java-enabled robotics software development environment version 2.0. The major highlights of Tue, 27 May 2008 19:35:50 GMT Terry Grant http://tech.groups.yahoo.com/group/Sumo11users/message/533 http://tech.groups.yahoo.com/group/Sumo11users/message/533 Ronald, One more thing, to use IC v.4.30 on your Sumo11, all you have to do is reload the firmware. V.5.01 did have fixes for the HB & Sumo11, but KISS didn't Tue, 27 May 2008 16:46:41 GMT Terry Grant http://tech.groups.yahoo.com/group/Sumo11users/message/532 http://tech.groups.yahoo.com/group/Sumo11users/message/532 Ronald, I know that the latest IC still loads version 4.30 to other targets such as Sumo 11. I'd look for other reasons for the crash. If your battery is weak Tue, 27 May 2008 13:39:01 GMT megagamml0r http://tech.groups.yahoo.com/group/Sumo11users/message/531 http://tech.groups.yahoo.com/group/Sumo11users/message/531 HI! I own a Sumo11 Board with IC 5.01 on the Sumo11 Board ... So I wanted to start Interactive C to programm a little bit but then when I need to choose Tue, 29 Jan 2008 22:25:55 GMT Dan Gates http://tech.groups.yahoo.com/group/Sumo11users/message/530 http://tech.groups.yahoo.com/group/Sumo11users/message/530 It sounds like you might have some part installed incorrectly or in the wrong spot. Check your diodes, they are polarized and have to be installed with the Tue, 29 Jan 2008 22:15:46 GMT Dan Gates http://tech.groups.yahoo.com/group/Sumo11users/message/529 http://tech.groups.yahoo.com/group/Sumo11users/message/529 Use pins 1 through 14, pin 1 should be labeled, but if not, pin 1 will be to the far left of the board closest to the side edge. Pins 15 & 16 are for the Tue, 22 Jan 2008 05:11:40 GMT autotheist http://tech.groups.yahoo.com/group/Sumo11users/message/528 http://tech.groups.yahoo.com/group/Sumo11users/message/528 I have a question about the connections on the LCD that came with the expansion board. There are 14 pins, and the LCD in the kit I got has 16 holes. Which 14 Fri, 11 Jan 2008 02:53:36 GMT ompalopsychite http://tech.groups.yahoo.com/group/Sumo11users/message/527 http://tech.groups.yahoo.com/group/Sumo11users/message/527 I am using a standard serial port, and I checked that the cable and the port are able to connect to other brands of microcontrollers that I have. ... stage ... Thu, 10 Jan 2008 17:43:37 GMT Dan Gates http://tech.groups.yahoo.com/group/Sumo11users/message/526 http://tech.groups.yahoo.com/group/Sumo11users/message/526 Are you using a standard serial port, or are you going through a USB port simulator? ... all the ... correctly ... software Tue, 01 Jan 2008 22:49:03 GMT ompalopsychite http://tech.groups.yahoo.com/group/Sumo11users/message/525 http://tech.groups.yahoo.com/group/Sumo11users/message/525 Yes, the jumper is set to single board mode. Tue, 01 Jan 2008 04:36:42 GMT Dan Gates http://tech.groups.yahoo.com/group/Sumo11users/message/524 http://tech.groups.yahoo.com/group/Sumo11users/message/524 Chris, Do you have the jumper set to single board mode? -Dan Mon, 31 Dec 2007 07:33:51 GMT ompalopsychite http://tech.groups.yahoo.com/group/Sumo11users/message/523 http://tech.groups.yahoo.com/group/Sumo11users/message/523 I was wondering if someone could advise me on troubleshooting stage two of the assembly of the main board (ie. adding the CPU and serial connections and all), Mon, 03 Dec 2007 17:31:28 GMT Dan Gates http://tech.groups.yahoo.com/group/Sumo11users/message/522 http://tech.groups.yahoo.com/group/Sumo11users/message/522 On the Sumo11, I sacrificed the second two PWM ports to create the servo ports. There is a detailed chart of how the ports are broken up in the Expansion board Fri, 04 May 2007 16:33:19 GMT nick987121 http://tech.groups.yahoo.com/group/Sumo11users/message/521 http://tech.groups.yahoo.com/group/Sumo11users/message/521 I have the need to drive 3 large 12v motors. I have already made 3 H-Bridge controllers using the NC LMD18200T IC's. I cannot figure out by the schematic, if Wed, 04 Apr 2007 13:32:38 GMT eetmajor2001 http://tech.groups.yahoo.com/group/Sumo11users/message/520 http://tech.groups.yahoo.com/group/Sumo11users/message/520 Thanks, i figured it out. I am still waiting approval to be added to the Robojde group. My problem was you can't change the baud rate on version 1.2.0. The