http://groups.yahoo.com/group/hf47158toCNC_Moderated/ hf47158toCNC_Moderated Sat, 18 Apr 2009 19:55:10 GMT Guy Lopes http://groups.yahoo.com/group/hf47158toCNC_Moderated/message/1293 http://groups.yahoo.com/group/hf47158toCNC_Moderated/message/1293 Hello all, I have been waiting to be approved on the old unmoderated site. I know that the spam became out of control, and thanks for making this improved Mon, 09 Mar 2009 21:12:21 GMT Ian Phillips http://groups.yahoo.com/group/hf47158toCNC_Moderated/message/1292 http://groups.yahoo.com/group/hf47158toCNC_Moderated/message/1292 ... Went to investigate speed controller fault today but before I started removing motor and top cover I ran the mill and it just worked normally! The fault Sun, 08 Mar 2009 17:52:52 GMT Greg http://groups.yahoo.com/group/hf47158toCNC_Moderated/message/1291 http://groups.yahoo.com/group/hf47158toCNC_Moderated/message/1291 ... I built a similar device for my mill, works pretty well as long as you keep the vac filter clean. I'm using a little 1 gallon vac, probably works a lot Sat, 07 Mar 2009 21:40:20 GMT Ian Phillips http://groups.yahoo.com/group/hf47158toCNC_Moderated/message/1290 http://groups.yahoo.com/group/hf47158toCNC_Moderated/message/1290 ... Craig I will check the relays, strange thing is that I am sure I have not overloaded anything, one look at the 'food mixer' quality gear arrangement made Sat, 07 Mar 2009 21:36:09 GMT Ian Phillips http://groups.yahoo.com/group/hf47158toCNC_Moderated/message/1289 http://groups.yahoo.com/group/hf47158toCNC_Moderated/message/1289 ... Jim I hope to have a look at the controller tomorrow, thanks for your tips. I have PCB repair skills and (unusually for me) not yet taken it apart to see Sat, 07 Mar 2009 20:21:03 GMT Craig Howarth http://groups.yahoo.com/group/hf47158toCNC_Moderated/message/1288 http://groups.yahoo.com/group/hf47158toCNC_Moderated/message/1288 Joyfully the relays on the control board are a little prone to welding in the closed position if you overload the motor for a period of time. The one in the Sat, 07 Mar 2009 19:32:38 GMT Jim RabidWolf http://groups.yahoo.com/group/hf47158toCNC_Moderated/message/1287 http://groups.yahoo.com/group/hf47158toCNC_Moderated/message/1287 Check the pot with an ohmmeter an the leads - DON'T touch the pots on the board! Failing that, check the board for burnt or cracked (cold) solder joints. But Fri, 06 Mar 2009 22:30:29 GMT Ian Phillips http://groups.yahoo.com/group/hf47158toCNC_Moderated/message/1286 http://groups.yahoo.com/group/hf47158toCNC_Moderated/message/1286 My mill (not yet CNCd) has the standard motor and speed control. Yesterday it was working just fine but when I switched on at the wall this afternoon the motor Thu, 05 Mar 2009 01:33:49 GMT ndhr23a http://groups.yahoo.com/group/hf47158toCNC_Moderated/message/1285 http://groups.yahoo.com/group/hf47158toCNC_Moderated/message/1285 I was looking for something to cover my exposed t-slots to keep swarf out and found that used windshield wiper blade refills are nearly perfect. Upside down Wed, 04 Mar 2009 07:55:43 GMT cffabrications http://groups.yahoo.com/group/hf47158toCNC_Moderated/message/1284 http://groups.yahoo.com/group/hf47158toCNC_Moderated/message/1284 I love it! I'm going to do something very similar to mine... Wed, 04 Mar 2009 01:07:46 GMT John Guenther http://groups.yahoo.com/group/hf47158toCNC_Moderated/message/1283 http://groups.yahoo.com/group/hf47158toCNC_Moderated/message/1283 Good Evening, I just uploaded two photos of my Swarf Collection System which was inspired by David Morrow over on the SherlineCNC group. It is quite simple, Tue, 23 Dec 2008 21:24:06 GMT Greg http://groups.yahoo.com/group/hf47158toCNC_Moderated/message/1282 http://groups.yahoo.com/group/hf47158toCNC_Moderated/message/1282 ... 22nd ... cold in ... Mine shipped out from LMS yesterday or today. I only have a couple small things I want to cut before I pull my mill apart. Went with Tue, 23 Dec 2008 19:19:11 GMT Darkith http://groups.yahoo.com/group/hf47158toCNC_Moderated/message/1281 http://groups.yahoo.com/group/hf47158toCNC_Moderated/message/1281 No, I don't think I responded. John did come through in the end. Kit was originally ordered on Jun 22nd (after he said he was caught up with his orders and Mon, 22 Dec 2008 23:00:33 GMT Greg http://groups.yahoo.com/group/hf47158toCNC_Moderated/message/1280 http://groups.yahoo.com/group/hf47158toCNC_Moderated/message/1280 ... FYI... LMS shows these are back in stock, when I emailed them a couple weeks ago they said they were getting 20 or 30 so they should have stock for a Mon, 15 Dec 2008 01:15:53 GMT Greg http://groups.yahoo.com/group/hf47158toCNC_Moderated/message/1279 http://groups.yahoo.com/group/hf47158toCNC_Moderated/message/1279 ... Hopefully he is cranking them out right now. I'm hoping LMS will have these in stock very soon as I broke more gears on mine again and can't see throwing