indica-users at Yahoo! Groups

Re: Wheel bearing noise or driveshaft CV bearing noise

Dev Abhishek — Sun, 19 May 2013 19:09:41 GMT

Hi Ashish, Most good TASCs should use a press, and you can specifically ask them if they do. Some may cut corners to save time, since the hammer method will

Re: Wheel bearing noise or driveshaft CV bearing noise

aashish — Sun, 19 May 2013 18:17:30 GMT

Thanks Dev, Yes, I agree it is a routine job. However, I wanted to get it done with the best possible way. I read online that even ASCs resort to hammer method

Re: Wheel bearing noise or driveshaft CV bearing noise

Dev Abhishek — Sun, 19 May 2013 17:58:24 GMT

Wheel bearing replacement is a routine job - any TASC should be able to handle it. If you are taking it to a local mechanic (as I do with my Jeep), they will

Re: Wheel bearing noise or driveshaft CV bearing noise

Deepak R Umrankar — Sun, 19 May 2013 17:23:25 GMT

Hi Ashish, I had got my rear wheel bearing replaced during the 100K service from Venus Auto, Chinchwad. I am not sure if he has the facility to fit the

Re: Screeching sound from pulley

murthytvr@... — Sun, 19 May 2013 15:47:43 GMT

Dear Aashis, Thanks for the guidance I will check the compression test and shall get back. Murthy.TVR Sent from BlackBerry� on Airtel ... From: "aashish"

Re: Wheel bearing noise or driveshaft CV bearing noise

aashish — Sun, 19 May 2013 15:14:29 GMT

I need further help specially Deepak- I followed up by jacking the car and found both front bearing making noise. However, I was not sure if both of them need

Re: Screeching sound from pulley

aashish — Sun, 19 May 2013 15:09:21 GMT

Hi Murthy TVR, Regarding piston rings, it's major job involving dismantling of the engine. So, make sure you take second opinion before simply going for that

Re: Screeching sound from pulley

murthytvr@... — Sun, 19 May 2013 07:23:18 GMT

Dear Deepak Ji, Many thanks for the prompt suggestions. ... Will replace the piston rings so the job. 2. I will take it to TVS service center. 3. The tappet

Re: Screeching sound from pulley

Deepak R Umrankar — Sun, 19 May 2013 06:46:22 GMT

Hi Murthy TVR, ... Bennarghata Road Bangalore. The mechanic said the belt on alternator is loose and immediately tightened it. The running is smooth now. Yes,

Re: Screeching sound from pulley

Murthy.TVR — Sat, 18 May 2013 22:32:51 GMT

Unable to stand the sound yesterday I visited MyTVS near my office on Bennarghata Road Bangalore. The mechanic said the belt on alternator is loose and

Re: break issue

Rahul — Sat, 18 May 2013 18:31:40 GMT

... ### Yes, I think the mechanic is fully correct. It is the master cylinder which has gone wrong. In my car it failed within six years, when the same problem

Re: break issue

Dev Abhishek — Sat, 18 May 2013 13:01:48 GMT

Please check your brake fluid level regularly. If you are not losing fluid, and the braking is poor but consistent (i.e., the vehicle brakes in a straight

Re: break issue

murthytvr@... — Sat, 18 May 2013 11:47:46 GMT

Check break booster. Reg/ Murthy Sent from BlackBerry® on Airtel ... From: hemkant sharma Sender: indica-users@yahoogroups.com Date:

Re: break issue

kumars.vipin@... — Sat, 18 May 2013 11:13:05 GMT

Check break oil level. Sent on my BlackBerry® from Vodafone ... From: hemkant sharma Sender: indica-users@yahoogroups.com Date: Sat, 18

break issue

hemkant sharma — Sat, 18 May 2013 07:57:16 GMT

Dear Friends,i have an Indica DLS 2005, 60k kms. The problem is when i apply break to the car, sometimes the break paddle is fully depressed but the breaking