internationalbseriestractors at Yahoo! Groups

Re: Source for tie rod ends?

rdhaskell@... — Thu, 09 Jul 2009 23:02:48 GMT

You might also try a NAPA auto parts store. They may be the same as something automotive. On Thu, 09 Jul 2009 22:20:02 -0000 "Bill"

Re: Source for tie rod ends?

Bill — Thu, 09 Jul 2009 22:20:28 GMT

Ebay of Australia has new tie rod ends listed for the B414 & B275....but what I was getting at is they say they also fit the 434 & 444 tractors and these could

Re: Source for tie rod ends?

Dave Jones — Sun, 05 Jul 2009 13:07:03 GMT

Thanks Bill! I had done some surfing and have several places to check out and I will add this to my list. Thanks, again. dj _____ From:

Re: Source for tie rod ends?

Bill — Sat, 04 Jul 2009 20:49:54 GMT

Check out the link below. They list them for the B414 down close to the bottom of the page and I would think the B275 is the same. If it isn't, they have an

Source for tie rod ends?

Dave Jones — Sat, 04 Jul 2009 01:49:44 GMT

Fellow babies, I need to replace the tie rod ends on my B-275. Does anyone have a source? dj

Re: grille

Jim Jackson — Thu, 02 Jul 2009 12:42:04 GMT

... I ordered mine at http://www.tractorparts.co.uk/

grill

gasman46725 — Wed, 01 Jul 2009 03:11:22 GMT

Where do I order a new grill for my BD414?

Re: My new grille arrived

Andy bury — Tue, 30 Jun 2009 20:24:38 GMT

Looks good Jim , I am considering "Buy one or repair mine" for my B275 it will come to cost I suppose shipping will be less for me here in the U.K.

My new grille arrived

Jim Jackson — Tue, 30 Jun 2009 02:15:10 GMT

I finally got a new grille for my B250 restoration, Had to get it from the UK. Looks much better than the original that was smashed up. Look in the Photos

Re: 73 2400b motor locked up. time to sell it?

Andy bury — Mon, 29 Jun 2009 18:02:32 GMT

If there was no oil in the motor then crankshaft will be wrecked.The bearings on the conecting rods will be siezed to the crank .Add to this other damage may

73 2400b motor locked up. time to sell it?

pete lohr — Mon, 29 Jun 2009 17:49:49 GMT

well since i bought this thing i have just sunk thousands of doallars into it. i still have not got to enjoy it. after having the internal brakes fixed, the

Re: hydraulic fluid level

binderreb — Mon, 29 Jun 2009 12:38:40 GMT

Hey Folks: Thought I would drag this one out of the closet for a couple of questions. Now, don't laugh (a smile or chuckle is okay) at my ignorance, but do

Greasy Brakes

ztimessquare2000 — Mon, 22 Jun 2009 19:42:44 GMT

Has anyone replaced the seals that are on the shafts that carries the brake disks? Mine are getting oil soaked. Can I just remove the brakes and pop out the

NEED PISTON FOR B414 gas.

John Grenzenbach — Sat, 20 Jun 2009 23:15:19 GMT

Does anyone have a good used piston for a B414 gas motor. The motor is a BC 144. Thanks in advance. I will keep my fingers crossed. John

Re: Need one sleeve and piston B414 gas BC144 engine

Bill — Fri, 19 Jun 2009 18:24:03 GMT

My only suggestion would be to do some searching on the internet and try to locate someone or a dealer parting one out. I have seen this from time to time. The