irmxstuff at Yahoo! Groups

ICU and jobs

robert_d1968 — Fri, 26 Jun 2009 00:36:16 GMT

Hi there agian, I have a tempsonic board (8 channel) that is in use in the Irmx operating system. The program that runs this board reports a board fault, but

Re: Dos IRMX Partition

robert_d1968 — Wed, 24 Jun 2009 02:32:41 GMT

Ok, I I did an Attachdevice c_rmx3 as C_rmx3 It attached successfully. I then formatted it as named. I then restored the job files from a floppy drive... I

Re: Dos IRMX Partition

William.Calvert@... — Tue, 23 Jun 2009 19:01:12 GMT

Robert, I think Martin is right. I was thinking about version 2.3 and not iRMX for windows. According to my iRMX 2.2 commands manual, I think the duib for

Re: Sentinel Key

Richard N Carver — Mon, 22 Jun 2009 15:09:32 GMT

If you are using INtime with the iRMX Addon it may require a Sentinel Key. I believe it was sometime after INtime v2.3, maybe with INtime v3, that they started

Re: Dos IRMX Partition

mafalk62 — Mon, 22 Jun 2009 07:50:02 GMT

Robert, I've had a look at the DOSRMX ICU file and there I have found the following drives: RMX: C_RMX (5), C_RMX0 (0), C_RMX1 (1), C_RMX2 (2), C_RMX3 (3) and

Re: Sentinel Key

mafalk62 — Mon, 22 Jun 2009 07:28:18 GMT

To my knowledge, this is not part of the RMX OS.

Sentinel Key

robert_d1968 — Sat, 20 Jun 2009 11:41:23 GMT

I'm not sure if this is part of the IRMX software. But thought I should ask about it. The job that is running in the Irmx software Keeps putting up an error

Re: Dos IRMX Partition

robert_d1968 — Sat, 20 Jun 2009 11:40:54 GMT

Bill, I tried last night to attach the partition as hda3 using the "ad hda3 as hda3 n" It replied with no such command found... I'm using version 2.2, when

Re: Dos IRMX Partition

William.Calvert@... — Fri, 19 Jun 2009 15:15:34 GMT

Robert, The book says that if you don't specify the device format, named or physical, when you format the device, it will be formatted in the format used when

Re: Dos IRMX Partition

robert_d1968 — Fri, 19 Jun 2009 12:09:34 GMT

Bill, Thanks for the information... I did try a couple of days ago to attach it as Hda3 but not exactly like you have attached it... "ad hda3 as hda3 n" I

Re: Dos IRMX Partition

William.Calvert@... — Thu, 18 Jun 2009 23:15:45 GMT

Robert, If this doesn't work, let me know and I'll check further. Since you created two DOS partitions they should be partitions 1 and two (hda1 and hda2), so

Dos IRMX Partition

robert_d1968 — Thu, 18 Jun 2009 11:29:11 GMT

I have a machine that uses the IRMX software. This uses DOS 6.22 The pc is set to boot from dos and then load irmx with a command set in the autoexec.bat file

Dos IRMX partition

Robert Dunn — Thu, 18 Jun 2009 11:29:07 GMT

I have a machine that uses the IRMX software. This uses DOS 6.22 The pc is set to boot fromm dos and then load irmx with a command set in the autoexec.bat

Re: iRMX II (iRMX 286) development tools

Cliff Lardin — Fri, 13 Feb 2009 20:51:09 GMT

Hi Rich, Many thanks. I will ask them again, this time, being specific. Best, Cliff ... From: iRMX Stuff Subject: Re: [irmxstuff] iRMX

Re: iRMX II (iRMX 286) development tools

iRMX Stuff — Fri, 13 Feb 2009 20:40:38 GMT

Hi Cliff, I spoke with one of my contacts at TenAsys and he said they do sell a DOS-hosted OMF86_286 Development Kit which has all the OMF 86 and 286 tools