joecellfreeenergydevice at Yahoo! Groups

Re: milk sepator cell stack .... umm ... ontopic??

RobertW — Sat, 07 Nov 2009 23:06:43 GMT

Will , if you have a vacuum pump connect it and smear stickaflex around joints , vacuum will suck it into the gaps and seal it( you will see where the leaks

Re: milk sepator cell stack .... umm ... ontopic??

Lee — Sat, 07 Nov 2009 07:42:22 GMT

Or enclosing pipe around it. The recirculating idea might help cut down on the foaming. Lee On Nov 6, 2009, at 22:57, "Will Scarlet"

milk sepator cell stack .... umm ... ontopic??

Will Scarlet — Sat, 07 Nov 2009 07:00:20 GMT

hi guys .. i know this isnt joe cell exactly, but I had a question. as this joe cell thing was started with these cones, i was curious if ANYone knows how to

Re: this is a stage 3 cell?

Sebastian — Fri, 06 Nov 2009 08:03:31 GMT

Bernie, I prepared the water with the cell, charging 1amp for 1min, wait 10min, and charge again 9 times per day, and filtering every day… I make the sensor

Re: this is a stage 3 cell?

Bernie — Fri, 06 Nov 2009 07:24:55 GMT

Sebastian, The 8.3 volts is where Dave sensed a peak in the field strength, but it's very possible that had something to do with that particular cell, or how

Re: this is a stage 3 cell?

Sebastian — Fri, 06 Nov 2009 05:59:57 GMT

Bernie, then the voltaje to leave overnight it might to be 8.3V? or the voltaje that would resulted in 50uA in my cell? Thanks Sebastian. De:

Re: this is a stage 3 cell?

Bernie — Fri, 06 Nov 2009 00:32:29 GMT

A good cell will affect the engine performance from inside the cab without any connections at all, but I think a ground wire to the car frame helps. You can

Re: this is a stage 3 cell?

Bernie — Thu, 05 Nov 2009 23:22:28 GMT

That should be OK. Water conductivity varies a lot. Joe claims to get 1 amp with 12 volts. The only issue is keeping the water from heating up. Bernie ...

Re: this is a stage 3 cell?

Sebastian — Thu, 05 Nov 2009 21:28:43 GMT

The water seem like stage 3, but dont work in my car… And the voltage slowly decrease over the time, and never rise up again. The bubbles stay for a couple

Re: this is a stage 3 cell?

Sebastian — Thu, 05 Nov 2009 21:01:32 GMT

Bernie, In my cell, charge with 12V would resulted in 200 mA, in this case the water is to much conductive? Is the wrong water? Thanks Sebastian De:

Re: this is a stage 3 cell?

Bernie — Thu, 05 Nov 2009 16:40:34 GMT

In the Experimenter's guide, Alex talks about 1". The .5" came about because that's about the distance where Dave sensed the best coupling. Bernie ... From:

Re: this is a stage 3 cell?

Sebastian — Thu, 05 Nov 2009 13:42:43 GMT

Bernie, If I connect the cell to a vaccum port, it has to be a 0,5” gap or it can be more? Thanks Sebastian. De: joecellfreeenergydevice@yahoogroups.com

Panacea's Free Energy Suppression production

ashtweth_nihilistic — Tue, 03 Nov 2009 02:44:34 GMT

Finally guys a proposed solution at the end. Part 2 also has case files to help other inventors and shows due credit to the open source FREE energy community

Re: this is a stage 3 cell?

Bernie — Tue, 03 Nov 2009 00:30:20 GMT

I think it was 8.3 volts. Bernie ... From: Sebastian To: joecellfreeenergydevice@yahoogroups.com Sent: Monday, November 02, 2009 4:12 PM Subject: RE: [Joe Cell

Re: this is a stage 3 cell?

Sebastian — Tue, 03 Nov 2009 00:12:35 GMT

In this page http://magnetism.vfedtec.com/Celery.htm says that they left power on the cell all night at a peaked torsion state, using the voltage adjustment,