mtt-11-on-wafer at Yahoo! Groups

Re: Regarding the Findlen--Command to input Low frequency

Dylan Williams — Sun, 19 Oct 2008 17:00:29 GMT

Again, please see below. Dylan Williams National Institute of Standards and Technology dylan@... www.boulder.nist.gov/dylan [+1] (303) 497-3138

Re: Regarding the Findlen--Command to input Low frequency

vamsi_palukuru — Sun, 19 Oct 2008 03:42:28 GMT

Dear Dr. Dylan, Thanks for your answers, I have some few left 1. I could able to change in the program code so that i can change the default Low-frequency

Re: Regarding the Findlen--Command to input Low frequency

Dylan Williams — Sat, 18 Oct 2008 03:51:55 GMT

Dear Vamsi, Please see my answers below. I hope they resolve the problem. Dylan Dylan Williams National Institute of Standards and Technology

Regarding the Findlen--Command to input Low frequency

vamsi_palukuru — Sat, 18 Oct 2008 03:26:12 GMT

1. What is the command to input the low frequency in Findlen.? 2.Can these line standards be used to calibrate VNA using Wincal ? 3. What should be the length

Re: fabricating calibration kit for TRL

Dylan Williams — Tue, 03 Jun 2008 01:33:56 GMT

Dear Nima, FINDLEN is not a set of standards, but a program that is included when you download MultiCal. We used FINDLEN to help us design the lengths of the

Re: fabricating calibration kit for TRL

nima rouhi — Tue, 03 Jun 2008 01:30:11 GMT

Dear Dylan, I looked over the manual of MultiCal but couldn't find anything about FINDLEN standards. As I read one of your papers ("Comparison of SOLR and TRL

Re: fabricating calibration kit for TRL

Dylan Williams — Mon, 02 Jun 2008 21:52:54 GMT

Dear Nima, I am sorry, I should have been more specific. FINDLEN is part of the MultiCal Software package. You can find that in my website. Dylan ... Dylan

Re: fabricating calibration kit for TRL

nima rouhi — Mon, 02 Jun 2008 21:23:45 GMT

Dear Dylan, Thank you for your reply. I searched for this standard tool, FINDLEN, but I couldn't find any source. could you please send me some links to a

Re: fabricating calibration kit for TRL

Dylan Williams — Fri, 30 May 2008 12:56:19 GMT

Dear Nima, I don't believe that I have seen a specific set of design rules for a calibration set on silicon. However, I think that the standard tools like

fabricating calibration kit for TRL

nima_rouh — Fri, 30 May 2008 08:54:56 GMT

Hi, I want to fabricate a calibration kit (for TRL calibration method) on silicon substrate and the frequency range is 5 MHz - 20 GHz. I will appreciate it if

Re: Multical, dielectric constant

Dylan Williams — Mon, 19 May 2008 16:12:54 GMT

Dear Thomas, There are multiple solutions to the TRL problem, and it is possible that you got the wrong solution. But this should not happen if you put in a

Multical, dielectric constant

eitel.thomas — Mon, 19 May 2008 15:22:54 GMT

Hallo I have a little problem with using Multical I am trying to make a cal kit in stripline (0.5 - 10 GHz,epsilon_r = 7). So I simulated a short, open, thru

Re: TRL calibration method

nima rouhi — Fri, 16 May 2008 15:22:18 GMT

Dear Dylan, Thank you very much for your helpfull informaion. I really appreiate that. Best regards, Nima Dylan Williams wrote: Dear

Re: TRL calibration method

Dylan Williams — Thu, 15 May 2008 15:44:36 GMT

Dear Nima, You have a number of places to look. The book by Glenn Engen comes to mind as a good overall reference. To find out more about the foundations of

TRL calibration method

nima_rouh — Thu, 15 May 2008 15:31:01 GMT

Hi all, I was wondering if you have any resources or book (just give the name) regarding the calibration method(specially TRL). I'm new in the area of