http://groups.yahoo.com/group/ndcc/ ModelRailRoad, Nscale + DCC. Language: e Tue, 10 Nov 2009 18:50:06 GMT William Buvinger http://groups.yahoo.com/group/ndcc/message/22975 http://groups.yahoo.com/group/ndcc/message/22975 Try http://www.trainweb.org/nrmrc/dcc/conversions.html#bachmann. I don't know if this will help or not but they show putting DCC in a Bachmann 2-8-0. you night Mon, 09 Nov 2009 21:26:11 GMT Jerry Jankura http://groups.yahoo.com/group/ndcc/message/22974 http://groups.yahoo.com/group/ndcc/message/22974 Hi, Folks: Yesterday, I acquired a Bachmann 2-6-2 Prairie locomotive at a flea market. I'm wondering if anyone can point me to an article on installing a DCC Mon, 09 Nov 2009 18:44:57 GMT romanowm1 http://groups.yahoo.com/group/ndcc/message/22973 http://groups.yahoo.com/group/ndcc/message/22973 DCC Question: Has anyone installed a decoder in this type engine from Micro Ace? If so can you send me some directions and the type of decoder used. Non DCC Mon, 09 Nov 2009 17:46:05 GMT nd5s@... http://groups.yahoo.com/group/ndcc/message/22972 http://groups.yahoo.com/group/ndcc/message/22972 Lansing Model Railroad Club Show & Sale MSU Pavilion, East Lansing, Michigan Don't miss this show! Grown to be the Largest Club Sponsored Show in Michigan!! A Sun, 08 Nov 2009 23:26:31 GMT David Menard http://groups.yahoo.com/group/ndcc/message/22971 http://groups.yahoo.com/group/ndcc/message/22971 Hello, I foolishly volunteered to coordinate the NTrak layout at the NMRA show next July. What I looking for is someone who is willing to set up and run the Sun, 08 Nov 2009 22:34:23 GMT Lars http://groups.yahoo.com/group/ndcc/message/22970 http://groups.yahoo.com/group/ndcc/message/22970 Hi. My Zephyr is behaving strange. I have 3 or 4 sets of MU:ed locos using universal consisting. When I then selects another single loco, can be from a UT4 or Sat, 07 Nov 2009 21:55:41 GMT brucealcock http://groups.yahoo.com/group/ndcc/message/22969 http://groups.yahoo.com/group/ndcc/message/22969 If you have not registered yet, there is still time ? the Southern Plains N Scale Convention starts on Thursday, December 3rd with a trip to El Reno (once Sat, 07 Nov 2009 11:17:03 GMT Freddie Bell http://groups.yahoo.com/group/ndcc/message/22968 http://groups.yahoo.com/group/ndcc/message/22968 ... A suitable decoder is one that fits (the loco and your pocket!) There must be a dozen decoders that would suit, starting with affordable on the one end (eg Sat, 07 Nov 2009 10:41:13 GMT nu2thehobby http://groups.yahoo.com/group/ndcc/message/22967 http://groups.yahoo.com/group/ndcc/message/22967 Having purchased one of these recently I was keen to install a suitable decoder so was wondering if anyone recommends a particular decoder over any others, I Fri, 06 Nov 2009 11:23:55 GMT John Heitmann http://groups.yahoo.com/group/ndcc/message/22966 http://groups.yahoo.com/group/ndcc/message/22966 There may be a grain of truth in what your friend says, Tom, if the DCC decoders use a lot of back EMF for speed control. Identical motors so equipped will Fri, 06 Nov 2009 05:57:23 GMT Freddie Bell http://groups.yahoo.com/group/ndcc/message/22965 http://groups.yahoo.com/group/ndcc/message/22965 ... Well, maybe he was "lucky" and he just happened to get 2 engines that are indeed speed matched without needing any adjustment. It's not impossible given Fri, 06 Nov 2009 02:32:22 GMT Fred Gemmill http://groups.yahoo.com/group/ndcc/message/22964 http://groups.yahoo.com/group/ndcc/message/22964 Les, I had both throttles and purchased a kit to convert one of them to the other so that I would have two that were the same. The kit consisted of a new chip Thu, 05 Nov 2009 22:48:40 GMT John Colombo http://groups.yahoo.com/group/ndcc/message/22963 http://groups.yahoo.com/group/ndcc/message/22963 Just because they are DCC doesn't mean they are speed-matched; while engines from the same manufacturer with the same drive-train (motors, gears, etc.) Thu, 05 Nov 2009 22:38:28 GMT tomthornton http://groups.yahoo.com/group/ndcc/message/22962 http://groups.yahoo.com/group/ndcc/message/22962 One of my friends runs two stock DCC engines, he tells me , as they are DCC the speeds are aready matched I didn't say anything but just wonder, are they Thu, 05 Nov 2009 20:49:37 GMT MrDCC@... http://groups.yahoo.com/group/ndcc/message/22961 http://groups.yahoo.com/group/ndcc/message/22961 Tom - In a word "no"! You can view them at: http://www.nmra.org/standards/DCC/standards_rps/DCCStds.html -- Bruce Petrarca www.LitchfieldStation.com Arizona,