on3 at Yahoo! Groups

Re: Lane Stewart

rickshoup — Wed, 10 Feb 2010 01:30:30 GMT

But does it run too? Rick. ... From: "k27rgs" To: Sent: Tuesday, February 09, 2010 5:25 PM Subject: [on3] Lane

Shays-for sale! Shays-wanted!

Layton H. Snover — Tue, 09 Feb 2010 23:43:35 GMT

Hi all! for Sale: Pacific Coast Shay by Sunset Models, with new chain drive, Faulhaber motor, unpainted. for Sale: Pacific Coast Shay by Sunset Models, with

Lane Stewart

k27rgs — Tue, 09 Feb 2010 22:26:10 GMT

this maybe of interest cheers http://www.youtube.com/watch?v=OIBynLPHXZI

Re: timonium

allenlandis — Tue, 09 Feb 2010 13:23:16 GMT

WOW That what I thought, it would be a wash out . Thanks Allen ... From: m2fq@... To: on3@yahoogroups.com Sent: Tuesday, February 09, 2010 7:10 AM

Re: timonium

m2fq@... — Tue, 09 Feb 2010 12:12:03 GMT

Allen et all, I'm glad I didn't! Heard thru the grapevine that 15 vendors showed up. Eight paid attendees on Saturday. About 250 on Sunday!

Timonium,Md.

allenlandis — Tue, 09 Feb 2010 03:08:32 GMT

Did anybody get to go to Timonium ? Wanted to go, but the weather kept me in the house. Allen

Re: Kemtron C-16

dave_grandt — Mon, 08 Feb 2010 17:39:45 GMT

I've uploaded a couple of photos of one of my Dad's C-16s with a music wire drive shaft. It uses .032 music wire (K&S), and parts from a kemtron X-291

Re: Kemtron C-16

Florian Barchetti — Mon, 08 Feb 2010 08:42:02 GMT

Hi Mike, actually there is not that much of a trick in soldering or brazing all sort of metals even aluminum. It is just a matter of useing the right mix

Re: Removing boiler off Bachmann On30 outside frame 2-8-0

Horace — Mon, 08 Feb 2010 04:27:04 GMT

Thanks Glenn I found the two screws under the cab. I already removed the one thru the saddle. Horace

Re: Kemtron C-16

ebtnut@... — Sun, 07 Feb 2010 21:08:58 GMT

Kemtron used to make a flux called Sal--Met. It was advertised as allowing you solder most anything, even Zamac. I think I may have used it in the past to

Re: Kemtron C-16

rickshoup — Sun, 07 Feb 2010 20:06:59 GMT

Oh well. Thanks anyway. rick ... From: "Horace" To: Sent: Sunday, February 07, 2010 2:25 PM Subject: [on3] Re: Kemtron

Re: Kemtron C-16

Glenn476 — Sun, 07 Feb 2010 19:47:45 GMT

I'll jump in since I did the same--The important thing is getting a straight hole in the square bar. I bored it in a Unimat using a 4-jaw chuck--this is a

Re: Removing boiler off Bachmann On30 outside frame 2-8-0

Glenn476 — Sun, 07 Feb 2010 19:33:16 GMT

have you tried the "Ask the Bach Man" site? They have an On30 sub site and someone will probably get back to you before the official guy does. My engine is in

Re: Kemtron C-16

Horace — Sun, 07 Feb 2010 19:26:01 GMT

Rick: That was like 30 years ago and I don't recall what I did. I believe I used Hobbytown U joints. I sold it a long time ago and do not kow were it went

Removing boiler off Bachmann On30 outside frame 2-8-0

Horace — Sun, 07 Feb 2010 17:57:30 GMT

Searched but could not find anything. How do you take the boiler off the Bachmann outside frame 2-8-0? (without breaking anything) Horace