http://groups.yahoo.com/group/radio-programming/ To swap information about programming two-way radio equipment and enabling options that aren't commonly known about. Focusing o Sun, 06 Jul 2008 21:56:41 GMT scanner4 http://groups.yahoo.com/group/radio-programming/message/49614 http://groups.yahoo.com/group/radio-programming/message/49614 How do I keep the clock set to the right time??? It loses time at 5 minutes per day or more HT-1250 AAH25RDF9AA5AN [Non-text portions of this message have Sun, 06 Jul 2008 20:26:42 GMT ANTHONY JENKINS http://groups.yahoo.com/group/radio-programming/message/49613 http://groups.yahoo.com/group/radio-programming/message/49613 hi anybody know where i can get this software it is for thef 500 radio i think thatsthe model tried the sites no luck but i may have got it wrong regards &73 Sun, 06 Jul 2008 19:48:38 GMT Eric Lemmon http://groups.yahoo.com/group/radio-programming/message/49612 http://groups.yahoo.com/group/radio-programming/message/49612 Mark, Some MaxTrac mikes have only one wire in the hang-up circuit, and must be hung on a grounded clip in order to take the radio out of monitor mode. Later Sun, 06 Jul 2008 19:21:41 GMT Mark Wilbur http://groups.yahoo.com/group/radio-programming/message/49611 http://groups.yahoo.com/group/radio-programming/message/49611 I have a maxtrac 300 radio that the monitor light is stuck on... I have tried a new mic and have been told that this might be an option that must be changed Sun, 06 Jul 2008 14:56:12 GMT Eric Lemmon http://groups.yahoo.com/group/radio-programming/message/49610 http://groups.yahoo.com/group/radio-programming/message/49610 The version of HVN9025 CPS that you need depends upon which firmware load is in the radio and, of course, what version of CPS was last used to program the Sun, 06 Jul 2008 05:19:42 GMT n http://groups.yahoo.com/group/radio-programming/message/49609 http://groups.yahoo.com/group/radio-programming/message/49609 What CPS works, I tried CPS 4? Sun, 06 Jul 2008 05:01:10 GMT mike sanders http://groups.yahoo.com/group/radio-programming/message/49608 http://groups.yahoo.com/group/radio-programming/message/49608 We have installed several of these units.  All in all they are good.  However, on a downside, we have had one or two loose programming settings with large Sun, 06 Jul 2008 03:58:54 GMT finchy2003 http://groups.yahoo.com/group/radio-programming/message/49607 http://groups.yahoo.com/group/radio-programming/message/49607 Hi,I am having trouble with being able to recieve a group selcal from a gme TX7000 to a simoco srp9100 and srm9000. I am using encode and decode tone set Sun, 06 Jul 2008 02:58:45 GMT Clint http://groups.yahoo.com/group/radio-programming/message/49606 http://groups.yahoo.com/group/radio-programming/message/49606 ... Anyone have this???? Sat, 05 Jul 2008 19:44:45 GMT Doug Bade http://groups.yahoo.com/group/radio-programming/message/49605 http://groups.yahoo.com/group/radio-programming/message/49605 You might want to map a directory structure that is fat32.. not ntfs... like store your codeplugs on a flash drive.... they are normally fat32... I suspect Sat, 05 Jul 2008 19:37:08 GMT rfiemiguy http://groups.yahoo.com/group/radio-programming/message/49604 http://groups.yahoo.com/group/radio-programming/message/49604 ... Yes I have, and it does "seem" to work, but I can't get the program to map my archive directories properly, so I can't pull up a codeplug to modify it. It Sat, 05 Jul 2008 19:31:28 GMT rfiemiguy http://groups.yahoo.com/group/radio-programming/message/49603 http://groups.yahoo.com/group/radio-programming/message/49603 ... Yep; Tried that, same result - a small block blinking in the upper left hand corner of the box and the program does not appear to execute. Sat, 05 Jul 2008 18:01:14 GMT John http://groups.yahoo.com/group/radio-programming/message/49602 http://groups.yahoo.com/group/radio-programming/message/49602 If you don't have a floppy drive, I have seen mentioned making a DOS bootable CD from an image. I keep an old DOS computer around (actually 2 variations one Sat, 05 Jul 2008 17:55:50 GMT Derek http://groups.yahoo.com/group/radio-programming/message/49601 http://groups.yahoo.com/group/radio-programming/message/49601 hold the button on the top next to the volume knob (the C button i think) and the function button below the PTT button and turn the radio on.  hold both Sat, 05 Jul 2008 17:40:40 GMT Mike http://groups.yahoo.com/group/radio-programming/message/49600 http://groups.yahoo.com/group/radio-programming/message/49600 I am looking for the TQ3385 software for the LPE200 Edacs and MDX edacs radio equipment. Any help would be appreciated, Thank you.